Corrugating Machinery: Lineup DRY END EQUIPMENT

DOUBLE FACER

Double Facer model 66H/56H

A wide variety of papers and flutes can be produced stably at high speed! Non-crushing ballast mechanism and low noise!

56H Double facer

Standard/Option

Slide horizontally to see the table.

Machine Type 66H Double facer 56H Double facer
Max. Machine Speed 400m(15.75”)/min 300m(11.81”)/min
Machine Width 2,200mm (86.61”), 2,500mm (98.43”), 2,800mm (110.24”) 1,800mm (70.87”), 2,000mm (78.74”), 2,200mm (86.61”), 2,500mm (110.24”)
Standard
  • Idler rolls
  • Short press loading pressure control device
  • Automatic and pneumatic constant tensional belt tightener
Option
  • Preheat roll with belt type driving device for bottom liner(450mm dia.)
  • Automatic steam temperature control device
  • New Steam Chest (Energy-saving Type)

Specifications and designs are subject to change without prior notice and without any obligation on the part of manufacturer.

SLITTER SCORER MODEL

Slitter Scorer model 57H-V/57H-III

Mitsubishi Heavy Industries Machinery Systems's Auto Slitter Scorer use advanced technology to give High Speed, High flexibility, Small lot control, and Quick Setups!

New Model 57H-V

Short setup time with servo-motorized plunge head movement.
This means quick order change with less waste paper.
Positioning accuracy of each head: +/- 0.5mm
Automatic web guide ensures stgable slitting and saves waste trim.(option)
Auto knife height-adjusting device enables easy maintenance.

57H-V Auto Slitter Score
57H-V Auto Slitter Score
57H-III Auto Slitter Score
57H-III Auto Slitter Score

Standard/Option

Slide horizontally to see the table.

Machine Type 57H-V Auto slitter scorer 57H-III Auto slitter scorer
Max. Machine Speed 400m(15.75”)/min 400m(15.75”)/min
Machine Width 1,800mm (70.87”), 2,000mm (78.74”), 2,200mm (86.61”), 2,500mm (98.43”) 1,800mm (70.87”), 2,000mm (78.74”), 2,200mm (86.61”), 2,500mm (98.43”), 2,800mm (110.24”)
Max. Box-out Number 7box-out 8box-out (note)
Min. Slitting Width 190mm (7.48”) 160mm (6.30”)
Min. Scoring Width 0mm (Min. Width of same shaft: 120mm (4.72”))
Standard
  • Lower knife slitting
  • Driving shafts for slitter knife and lower scorer head
  • Rising and lowering control for each slitter knife and upper scorer head
  • Vacuum paper dust removal device
  • Individual knife support roll
  • Automatic individual resharpening device for each slitter knife
  • Single unit operation control system
  • Double-run control device for No.1 and No.2 unit (for scorer only)
  • Lower knife slitting
  • Driving shafts for slitter knife and lower scorer head
  • Rising and lowering control for each slitter knife and upper scorer head
  • Vacuum paper dust removal device
  • Individual adjusting device of slitting depth
  • Automatic individual resharpening device for each slitter knife
  • Single unit operation control system
  • Double-run control device for No.1 and No.2 unit (for scorer only)
Option
  • Edge cut device (56-2G)
  • Steering guide
  • Edge cut device (56-2G)
  • Individual knife support roll
  • For 2,500-2,800mm width machine.

Specifications and designs are subject to change without prior notice and without any obligation on the part of manufacturer.

CUTOFF

Cutoff model 68H/58H

Aluminium hollow cylinder reduces energy consumption while producting at high speeds with high accuracy.
The Mitsubishi Heavy Industries Machinery Systems Cutoff, “68H” and “58H”!

58H Cutoff
58H Cutoff

Standard/Option

Slide horizontally to see the table.

Machine Type 58H Cutoff 68H Cutoff
Max. Machine Speed 375m(14.76")/min 400m(15.75")/min
Machine Width 1,800mm (70.87"), 2,000mm (78.74"), 2,200mm (86.61"), 2,500mm (98.43") 2,200mm (86.61"), 2,500mm (98.43"), 2,800mm (110.24”)
Standard
  • Rotary type cutting
  • In-feed suction conveyor
  • Out-feed conveyor with sheet suppresser
Option
  • Special notch type blade (serrated/serrated+notch)
  • Special brushless motor for cutting (Max. 3motors)
  • Preprinted mark cutting device
  • Local cutting length indicator
  • Air conditioner for independent drive motor control panel
  • Flicker light for unusual condition
  • Paper dust removal device

Specifications and designs are subject to change without prior notice and without any obligation on the part of manufacturer.

STACKER

Stacker model 69J

High speed/Small lot stacker was developed with Shizuoka Koki. Minmum order change cycle is only 8 seconds!

69J Stacker

Standard/Option

Slide horizontally to see the table.

Machine Type 69J Stacker
Max Machine Speed 400m(15.75")/min
Machine Width 1,800mm (70.87"), 2,000mm (78.74"), 2,200mm (86.61"), 2,500mm (98.43")
Max. Sheet Stacking
Height		 1,800mm (70.87")
Min. Stacking
Sheet Width		 260mm (10.24")
Range of Stacking
Sheet Length		 500-3,000mm (19.69"-118.11")
Min. Stacking
Cycle Time		 8.0sec (No palette, No plywood)
9.0sec (Palette, Plywood) (note 1)
Standard
  • Dual suction typed order separator
  • Center stacking control
  • Back stop controlled by AC servo-motor
Option
  • Deflector type waste sheet removal device
  • Max. stacking sheet length 4,000mm
  • Cross conveyor for waste sheet removal
  • Auto pallet supplying device
  • Auto plywood supplying device
  • 1Cycle time above is subject to change depends on layouts and plywood/palette feeding devie.
  • 2For 2,500mm machine, min. stacking cycle time is 9.0sec (No palette, No plywood), and 10sec (Palette, Plywood).

Specifications and designs are subject to change without prior notice and without any obligation on the part of manufacturer.

PRODUCTION CONTROL SYSTEM SIGMA 2000

Production Control System model ∑2000

The best production control system for high production with many order changes and short paper cycles. Sigma 2000 maximizes corrugating machine performance and ensures easy operation!

∑2000 Production control system

Standard/Option

Slide horizontally to see the table.

Machine Type Production control system Σ2000
Standard
  • Wet end control panel
  • Dry end control panel
  • Bridge control function
  • Paper splicing speed control
  • Auto cruising
  • Order change speed control
  • Trouble solution by remote control
  • Production record summarize function
  • Preserved indication of data control
Options
  • Process control
  • Online data link
  • Production record printing
  • Auto flute gap control for loss reduction
  • Several kinds of indicators

Specifications and designs are subject to change without prior notice and without any obligation on the part of manufacturer.

Stories of MHI Group Expertise